Departures & SIDs
Releasing departures, climbing them clear of arrivals and handing them to the centre.
Departures are half of an approach controller's traffic. Your goal is simple: get each departure climbing as early and as high as possible, on its way to the en-route airspace, without conflicting with arrivals descending into the same airport.
1. Standard Instrument Departures (SIDs)
A SID is a published route from the runway to the en-route network, with altitude and speed restrictions. It keeps departures predictable and away from terrain and from arrival routes. Each SID ends at a fix where the airway begins, and has an initial climb level (for example 6,000 ft or FL130) designed to stay below the arrivals overhead.
2. Releasing departures
When several units work the same airport, Tower must not launch a departure into your airspace if it would conflict. Agree on a procedure with Tower:
- Free-flow: Tower may launch departures on the standard SIDs without asking, as long as they follow the agreed spacing.
- Release required: Tower asks you before each departure. "Levant two one eight ready, request release." – "Released."
Departures on the same SID need spacing from each other – often 2–3 minutes, or 5 NM radar, increasing if the second one is faster.
3. First contact and identification
Pilot: "Amman Approach, Levant two one eight, passing three tousand eight hundred feet for six tousand, LOSAR one charlie."
APP: "Levant two one eight, identified, climb flight level one five zero, no speed restriction."
Check the label and level, then give the next step as soon as it's safe. Pilots love an early, unrestricted climb – it saves fuel and keeps them away from arrivals.
4. Separating departures from arrivals
- Level: arrivals usually descend over the airport; departures climb underneath and out. Keep departures below arrivals until they are laterally clear, then climb.
- Turns: a short vector away from the arrival stream lets you climb earlier: "turn right heading zero four zero, climb flight level one five zero."
- Direct routings: once clear of the TMA's conflicts, send departures direct to the SID's exit fix or beyond: "proceed direct LOSAR, climb flight level two four zero."
5. Handing over to Centre
Before the aircraft reaches your upper or lateral boundary:
- Climb it to the level agreed with Centre (often written in the letter of agreement, e.g. "FL240 at the boundary").
- Make sure it is clear of all your traffic.
- Hand it over: "Levant two one eight, contact Amman Control one three two decimal niner, goodbye."
If Centre is offline, the aircraft continues on UNICOM: "Levant two one eight, radar service terminated, no ATC available, monitor UNICOM one two two decimal eight, goodbye."
6. Common departure problems
- Pilot flies the wrong SID: correct with a vector, then re-clear: "turn left heading two nine zero, then proceed direct ROMAR."
- Level bust (aircraft climbs through its cleared level): "Levant two one eight, stop climb flight level one three zero immediately, traffic…"
- Engine failure after take-off: the pilot will follow their own engine-out procedure – don't give turns or climbs, give priority and ask intentions.
Controlling it at Levant
At the start of a Levant group flight, ten or more departures may leave OJAI in a few minutes on the same SID. Agree free-flow with Tower, spacing of 2 minutes, and climb each one as soon as the one ahead is above them. Many Levant flights are long-haul, so a smooth climb to high levels matters.
Check yourself
- Why do SIDs have a low initial climb level? To keep departures below the arrivals until they are clear of each other.
- What is a "release"? Approach's permission for Tower to launch a departure into its airspace.
- Two departures on the same SID, the second faster. What do you do? Increase the spacing or turn/climb the second one so it doesn't catch up.
- What do you say when there is no next controller? "Radar service terminated, no ATC available, monitor UNICOM 122.800."
Simulation training material. LOSAR 1C (SID), MUNRA 1G (STAR) and the ILS Z runway 26R are real Queen Alia (OJAI) procedures; frequencies, other fixes and levels are examples. Always use the current charts and IVAO division procedures.