APP - Approach Control

Separation Standards

Vertical, radar and wake turbulence separation, and using speed and visual separation.

Lesson 2 of 5 4 min read 8 sections Updated Nov 9, 2026

Separation is the heart of air traffic control: the minimum distance two IFR aircraft must keep, vertically or horizontally, so they can never collide. A radar controller's main job is to make sure that at every moment, between every pair of aircraft, at least one separation minimum exists.

1. Vertical separation

  • 1,000 ft between aircraft up to FL410 in RVSM airspace (and below FL290 everywhere).
  • 2,000 ft above FL410, or for aircraft not approved for RVSM between FL290 and FL410.

An aircraft that has been cleared to leave a level may be considered to have left it once its Mode C shows a change of more than 300 ft in the cleared direction. You may then clear another aircraft to the level just vacated – but be careful with fast climbers and descenders.

2. Radar (horizontal) separation

  • 5 NM is the standard radar separation minimum.
  • 3 NM may be used within the approach area where the radar and procedures allow it (often within 40 NM of the radar).
  • On the same ILS final, reduced spacing such as 2.5 NM is allowed only where the state has approved it.

Measure the distance between the centres of the radar positions, and remember that two aircraft closing head-on at 250 kt each close 1 NM every 7 seconds.

3. Wake turbulence separation on approach

Behind heavier aircraft the radar spacing must be larger, because of the wake vortices:

LeaderFollowerMinimum
Super (A380)Heavy / Medium / Light6 / 7 / 8 NM
HeavyHeavy / Medium / Light4 / 5 / 6 NM
MediumLight5 NM

These apply when the follower is directly behind at the same level or less than 1,000 ft below, or on the same final approach.

4. Speed control

Speed is your fine-tuning tool for spacing on the same route:

  • "Levant two one eight, reduce speed two one zero knots." / "maintain one eight zero knots until four miles final."
  • Give speed changes of at least 20 kt, and not when the aircraft is below 4 NM final.
  • Typical limits: 250 kt below FL100, around 210–220 kt on the downwind and base, 160–180 kt on final.
  • Cancel restrictions clearly: "no speed restriction."

5. Visual separation

Inside controlled airspace below FL100, two aircraft can be separated visually: if a pilot reports the other traffic in sight, you may instruct them to maintain their own separation. "Levant two one eight, traffic twelve o'clock, four miles, Airbus three twenty on final, report in sight." – "Traffic in sight." – "Follow that traffic, cleared visual approach runway two six right." This is powerful in good weather, but only use it when both aircraft are clearly visible and the pilot confirms.

6. Building a "separation habit"

  • Scan the whole scope regularly, not only the aircraft you are talking to.
  • For every instruction ask: does this create a conflict in the next few minutes?
  • Use level first where you can – vertical separation is easy to see and to keep.
  • When two aircraft are converging at the same level and you are not sure, act early: a heading change at 20 NM is easy, at 6 NM it is an emergency.

Controlling it at Levant

In a group flight, most Levant aircraft are Mediums (A320, B737) with the odd Heavy (A330, B777, B787). Know which is which from the flight plan type, and give extra spacing behind the Heavies when you line them up for the same runway.

Check yourself

  1. Standard radar separation? 5 NM (3 NM where approved in the approach area).
  2. A Medium follows a Heavy on the same ILS. Minimum radar spacing? 5 NM.
  3. Vertical separation between two RVSM aircraft at FL370 and FL380? 1,000 ft – they are separated.
  4. When may you stop giving speed restrictions on final? Avoid speed changes inside 4 NM; cancel with "no speed restriction".

Simulation training material based on ICAO PANS-ATM (Doc 4444). Reduced minima depend on each state's approval.