APP - Approach Control

Terminal Airspace & Radar

TMAs and control zones, radar and transponders, identifying aircraft and the radar services you give.

Lesson 1 of 5 4 min read 8 sections Updated Nov 9, 2026

Approach control (APP) looks after the terminal area: the busy airspace where departures climb out and arrivals descend towards the runways. Almost all approach control today is radar control. You see every aircraft on your scope and you move them with headings, levels and speeds. This lesson explains the airspace you own and the radar tools you work with.

1. The terminal area

  • TMA (terminal control area): the block of controlled airspace around one or more airports, usually from a few thousand feet up to the base of the upper airspace. Amman Approach, for example, serves Queen Alia (OJAI), Amman Marka (OJAM) and the traffic between them.
  • CTR (control zone): the part from the ground up, around each airport, delegated to Tower.
  • Your sector has lateral limits and an upper limit; above it is the Centre, beside it neighbouring approaches.

Learn your sector file: the boundaries, the main fixes, the SIDs and STARs, the minimum altitudes and any restricted areas.

2. Primary and secondary radar

  • Primary radar sees reflections of any object – it needs nothing from the aircraft but gives no identity or altitude.
  • Secondary surveillance radar (SSR) interrogates the aircraft's transponder, which replies with its code (Mode A), its pressure altitude (Mode C) and, with Mode S, its callsign and more.

On IVAO your scope works like SSR: you see the squawk, the level and the callsign in each label – but only if the pilot's transponder is on and set correctly.

3. Identification

Before you can give radar service you must identify the aircraft – be sure which blip is which. Methods:

  • The aircraft squawks the assigned code and its label appears with the right callsign.
  • "Squawk ident": the label flashes when the pilot presses IDENT.
  • Position report: the pilot reports over a fix you can see on the scope.
  • A turn of 30° or more that you observe on the scope.

Tell the pilot: "Levant two one eight, identified, climb flight level one five zero." Also check the Mode C level: if the label shows 6,000 ft and the pilot reports 6,000 ft, it is verified. If it differs by 300 ft or more, ask the pilot to check the altimeter.

4. Transponder codes you must know

CodeMeaningYour reaction
7700EmergencyAsk the nature, give priority, offer the nearest suitable airport
7600Radio failureExpect the aircraft to follow the radio-failure procedure; keep others clear
7500Unlawful interferenceDo not ask about it on the radio; report it and keep others clear
2000 / 7000No code assigned / VFR conspicuityAssign a discrete code if you work the flight

5. Radar services and their terms

  • Radar vectoring: you give headings; the pilot leaves their own navigation. Always give the reason and the plan: "turn left heading three one zero, vectors ILS Z runway two six right."
  • Resume own navigation when vectoring ends: "resume own navigation direct ALPHA, track three five two, eight miles."
  • Traffic information uses the clock code from the aircraft's track: "traffic eleven o'clock, eight miles, opposite direction, one thousand feet above."
  • Radar service terminated when the flight leaves your area or radar control.

6. Minimum altitudes

When you vector an aircraft you become responsible for its terrain clearance. Use the minimum vectoring altitude (MVA) or minimum sector altitudes on your charts, and never assign a lower altitude. Around Amman the terrain rises above 3,000 ft; west of it the Jordan Valley drops far below sea level, and to the north-west the mountains of Lebanon rise above 10,000 ft. Know your MVA chart before you vector anyone.

Controlling it at Levant

Approach is where a Levant group flight is won or lost: twenty aircraft arriving at the same airport within half an hour need a controller who identifies them early, keeps the labels readable and starts sequencing long before they reach the airport.

Check yourself

  1. Name two ways to identify an aircraft. Assigned code, squawk ident, position report over a fix, an observed turn.
  2. The label shows FL143, the pilot reports FL150. What do you do? The difference is 300 ft or more: ask the pilot to check the altimeter setting / level.
  3. What must you protect when you vector an aircraft? Terrain clearance: never below the minimum vectoring altitude.
  4. An aircraft squawks 7600. What does it mean? Radio failure.

Simulation training material based on ICAO PANS-ATM (Doc 4444). Sector limits and altitudes are examples: use the current IVAO division charts and sector files.